Aerosol

POLYCHEM 7528-M-60

Polychem 7528-M-60 (Z8206)

Polychem 7528-M-60 is an vinyl toluene modified alkyd supplied at 60% in a narrow cut aliphatic hydrocarbon solvent, providing a flash point of greater than 100 degrees F, but at the same time allowing for faster dry than standard mineral spririt cuts. This product is low-HAP and can be formulated into HAP-free coatings (below 1% HAP).

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 60
Viscosity, G-H Z2-Z4
Acid Number 12
Gardner Color 6 Maximum
Weight Per Gallon 7.65 ± 0.1
Solvent Quick Drying Mineral Spirits
Modifier VT
Oil Soybean Oil
Reduced Viscosity F-H
Reduced NVM 40
Reduction Solvent Quick Drying Mineral Spirits
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Aerosols
Metal furniture and toy finishes
Floor sealers

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.03%
Calcium 0.02%
Zirconium 0.30%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged , ,

POLYCHEM 7520-M-60

Polychem 7520-M-60 (Z8130)

Polychem 7520-M-60 is an vinyl toluene modified linseed oil in a narrow cut aliphatic hydrocarbon, providing a flash point of greater than 100 degrees F, (combustible range), but at the same time allowing for faster dry than standard mineral spirit cuts. This product is low-HAP and can be formulated into HAP-free coatings (below 1% HAP).

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 60
Viscosity, G-H X-Z1
Acid Number 13
Gardner Color 7 Maximum
Weight Per Gallon 7.45 ± 0.1
Solvent Quick Drying Mineral Spirits
Modifier VT
Oil Linseed Oil
Reduced Viscosity D-E
Reduced NVM 40
Reduction Solvent Quick Drying Mineral Spirits
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Sanding sealers with improved open time
Equipment and metal furniture enamels
Miscellaneous fast air dry industrial or trade sale finishes

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.01%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged , ,

POLYCHEM 7519-B-70

Polychem 7519-B-70 (Z8126)

Polychem 7519-B-70 is an styrene/acrylic modified alkyd designed for air dry, force dry, or bake finishes providing a good degree of flexibility and good projected durability / color retention. This product is low-HAP and can be formulated into HAP-free coatings (below 1% HAP).

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 70
Viscosity, G-H W-Z
Acid Number 14
Gardner Color 5 Maximum
Weight Per Gallon 8.4 ± 0.1
Solvent BLEND
Modifier ACR
Oil Soybean Oil/Sunflower Oil
Reduced Viscosity E-G
Reduced NVM 60
Reduction Solvent METHYL n-PROPYL KETONE MPK
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Farm implements / equipment
Metal product finishes
Bake enamels

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.03%
Zirconium 0.30%
Calcium 0.03%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged ,

POLYCHEM 7459-X-50

Polychem 7459-X-50 (Z2301)

Polychem 7459-X-50 is an fast drying acrylic modified alkyd for applications where good flexibility and gloss / color retention are desired.

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 50
Viscosity, G-H N-R
Acid Number 14
Gardner Color 4 Maximum
Weight Per Gallon 8 ± 0.1
Solvent Xylene
Modifier ACR
Oil Dehydrated Castor Oil
Reduced Viscosity
Reduced NVM
Reduction Solvent
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Farm Implement / Equipment
Metal Product Finishes
Bake Enamels with melamines and ureas

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.05%
Zirconium 0.50%
Calcium 0.03%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged ,

POLYCHEM 7447-BA-80

Polychem 7447-BA-80 (Z8042)

Polychem 7447-BA-80 is an very fast air drying vinyl toluene copolymer resin supplied at 80% solids in n-butyl acetate. It is useful as the binder in aerosol formulations, industrial enamels and sanding sealers. This product is low-HAP and can be formulated into HAP-free coatings (below 1% HAP).

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 80
Viscosity, G-H Z4-Z6
Acid Number 16
Gardner Color 6 Maximum
Weight Per Gallon 8.3 ± 0.1
Solvent n Butyl Acetate
Modifier VT
Oil Soybean Oil
Reduced Viscosity D-F
Reduced NVM 60
Reduction Solvent n Butyl Acetate
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Aerosol coatings
Wood finishes
Sanding sealers
Industrial enamels

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.02%
Zirconium 0.20%
Calcium 0.02%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged ,

POLYCHEM 7447-X-80

Polychem 7447-X-80 (Z8041)

Polychem 7447-X-80 is an very fast air drying vinyl toluene co-polymer resin supplied at 80% solids in xylene. It is useful as the binder in aerosol formulations, industrial enamels and sanding sealers.

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 80
Viscosity, G-H Z4-Z6
Acid Number 16
Gardner Color 6 Maximum
Weight Per Gallon 8.3 ± 0.1
Solvent Xylene
Modifier VT
Oil Soybean Oil
Reduced Viscosity D-F
Reduced NVM 60
Reduction Solvent Xylene
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Aerosol coatings
Wood finishes
Sanding sealers
Industrial enamels

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.02%
Zirconium 0.20%
Calcium 0.20%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged ,

POLYCHEM 7410-M-60

Polychem 7410-M-60 (Z8010)

Polychem 7410-M-60 is an vinyl toluene modified alkyd for use in air dry or forced dry applications. This product is HAPS free.

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 60
Viscosity, G-H Z-Z2
Acid Number 10
Gardner Color 5 Maximum
Weight Per Gallon 7.7 ± 0.1
Solvent Mineral Spirits, Low Aromatic
Modifier VT
Oil Soybean Oil
Reduced Viscosity E-G
Reduced NVM 40
Reduction Solvent Mineral Spirits, Low Aromatic
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Equipment and metal furniture enamels
Fast air dry, Industrial or Trade Sales finishes

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.02%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged ,

POLYCHEM 7378-X-52

Polychem 7378-X-52 (Z7986)

Polychem 7378-X-52 is an styrenated soya alkyd showing excellent dry and a good balance of performance properties.

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 52
Viscosity, G-H U-W
Acid Number 16
Gardner Color 5 Maximum
Weight Per Gallon 8.1 ± 0.1
Solvent Xylene
Modifier STY
Oil Soybean Oil
Reduced Viscosity C-F
Reduced NVM 37
Reduction Solvent Xylene
Clarity 10 Max

 

SUGGESTED USES
Fast drying enamels
Industrial finishes

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
(not specified)
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged ,

POLYCHEM 7147-V-50

Polychem 7147-V-50 (Z7648)

Polychem 7147-V-50 is an fast drying vinyl toluene alkyd that achieves durable high gloss finishes with exceptional water and solvent resistance. It exhibits excellent surface wetting and adhesion combined with the usual fast set and dry of a vinyl toluene alkyd. It is an exceptional value in non-burning, high quality aerosol paints for plastics and styrofoam. This product is low-HAP and can be formulated into HAP-free coatings (below 1% HAP).

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 50
Viscosity, G-H Z-Z2
Acid Number 12
Gardner Color 5 Maximum
Weight Per Gallon 7.45 ± 0.1
Solvent VM&P
Modifier VT
Oil Soybean Oil
Reduced Viscosity S-U
Reduced NVM 40
Reduction Solvent VM&P
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Implement enamels, trailer finishes, aerosols, metal primers, toy enamels, paper coatings, fogless mill whites, binder-sealers for chalky cement paints and sanding sealers.

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.05%
Zirconium 0.50%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged ,

POLYCHEM 7138-V-50

Polychem 7138-V-50 (Z7640)

Polychem 7138-V-50 is an vinyl toluene modified alkyd with “high drink” properties. This product is low-HAP and can be formulated into HAP-free coatings (below 1% HAP).

CHARACTERISTICS SPECIFICATIONS
Percent Non Volatile 50
Viscosity, G-H Z2-Z4
Acid Number 8
Gardner Color 5 Maximum
Weight Per Gallon 7.45 ± 0.1
Solvent VM&P
Modifier VT
Oil Linseed Oil / Soybean Oil
Reduced Viscosity M-O
Reduced NVM 35
Reduction Solvent VM&P
Clarity CLEAR TO SLIGHTLY HAZY

 

SUGGESTED USES
Fast dry lacquers
Implement enamels
Aerosols

 

DRIER RECOMMENDATIONS (% metal on total binder solids)
Cobalt 0.05%
Zirconium 0.50%
The information and specifications stated here are for the material currently offered, are subject to change without prior notice, and due to variations in user handling and application methods should not be relied upon without testing under user conditions. The supplier makes no warranty of any kind, express or implied, concerning this product or its use either singly or in combination with other substances. User assumes all risks incident to its use. User must communicate to employees and customers all warnings that relate to the potential exposure to this product. The user assures that workplace and disposal practices are in compliance with laws, regulations and ordinances. ALL WARRANTIES, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL THE SUPPLIER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
Tagged ,